TS-850: Difference between revisions

From Tučňák Wiki
Jump to navigation Jump to search
Ok1zia (talk | contribs)
No edit summary
Ok1zia (talk | contribs)
No edit summary
 
(6 intermediate revisions by the same user not shown)
Line 34: Line 34:
=IF OUT=
=IF OUT=
[[Image:Ts850s_ifout.png|none|frame|TS-850s IF OUT konektor]]
[[Image:Ts850s_ifout.png|none|frame|TS-850s IF OUT konektor]]
=CAT=
[[Image:Ts850s_cat.png|none|frame|TS-850s IF OUT konektor]]


=Blokový diagram=
=Blokový diagram=
[[Image:TS-850 BlockDiagram.png|none|frame|Blokový diagram TS-850s]]
[[TS-850 BlockDiagram]]
 
 
=Servisní menu=
 
Pressing SCAN + TX-M.CH will set the radio into its extended function mode. These options can be scrolled via the M.CH/VFO CH. switch. The following are the extended functions:
 
* 00 - This is the ROM Ce`ecksum displayed as a 4-digit hexadecimal number. This cannot be changed.
* 01 - Allow filter selection in transmit. Initially set OFF.
* 02 - Antenna tuner power down.  Initially set to OFF.
* 03 - Antenna tuner non-stop mode.  When set to on, the antenna tuner will not stop when the lowest VSWR is found. Initially set to OFF.
* 04 - Store mode, and filter settings prior to changing bands, or channels.  Initially set to ON.
* 05 - Display -HELLO- on digitial display, and send it in Morse code on power up.  Initially set OFF.
* 06 - Turn full LCD display ON on power on.  Initially set OFF.
 


=Naměřené hodnoty=
=Naměřené hodnoty=

Latest revision as of 13:10, 9 November 2010

Nastavení pro optimální čistotu signálu

  • CAR = max
  • PROC = 7
  • MIC = max
  • PWR = max
  • RF = max
  • NB1 = on
  • NB2 = off
  • MONI = 1
  • PROC = on
  • MONI = on
  • VOX = on
  • Dávač = skoro max

Nastaveni pro buzeni LT2S+DB6NT

  • CAR = max
  • PROC = 7
  • MIC = 6

Nastavení podle OK3RM

K rozumnému nastavení slouží měřidlo na TS850ce, kde si zapneš na měřáku PROC a nastavíš si max. 10dB kompresi. Pak si zapneš ALC a nastavíš si hladinu MIC maximálně na konec rozsahu ALC, když hodně moduluješ.

Propojení s LT2S

  • Do IF OUT musí být přivedeno +12V pro zapnutí IF OUT a vypnutí PA.
  • V REMOTE konektoru musí být propojeny piny +12 VDC on transmit (7) se Speaker output (1). Na kusu OK1MZM je na Speaker output zapojené zapnutí IF OUT.
    TS-850s remote konektor
  • Přepínač LINEAR AMP na zadním panelu musí být zapnutý

Klíčování

Při klíčování mikrofonním konektorem

TS-850s mikrofonní konektor

nelze mezi piny STBY (2) a GND (8) použít optočlen s Darlingtonem. Na něm je totiž velký úbytek cca 0.7 V a rádio zaklíčuje jen "napůl". Červená LED na předním panelu se rozsvítí, ale na Meteru se nepřepne zobrazení na SWR (dle nastavení) a modulace je silně zkreslená (velmi slabá, jen basy). Funguje klíčování obyčejným optočlenem typu 4N26.

ACC2

TS-850s ACC2 konektor

IF OUT

TS-850s IF OUT konektor

CAT

TS-850s IF OUT konektor

Blokový diagram

TS-850 BlockDiagram


Servisní menu

Pressing SCAN + TX-M.CH will set the radio into its extended function mode. These options can be scrolled via the M.CH/VFO CH. switch. The following are the extended functions:

  • 00 - This is the ROM Ce`ecksum displayed as a 4-digit hexadecimal number. This cannot be changed.
  • 01 - Allow filter selection in transmit. Initially set OFF.
  • 02 - Antenna tuner power down. Initially set to OFF.
  • 03 - Antenna tuner non-stop mode. When set to on, the antenna tuner will not stop when the lowest VSWR is found. Initially set to OFF.
  • 04 - Store mode, and filter settings prior to changing bands, or channels. Initially set to ON.
  • 05 - Display -HELLO- on digitial display, and send it in Morse code on power up. Initially set OFF.
  • 06 - Turn full LCD display ON on power on. Initially set OFF.


Naměřené hodnoty

Kus OK1MZM

CAR PWR výkon [W] odstup šumu [dBc/Hz]
6 0 3.3 -114.17
7 0 10 -119.33
10 1 25 -131.2
max max 87 -132.4