CW keying

Tucnak keys and sends CW itself (since version 2.0 it does not need the external program cwdaemon).
Check Enabled to use CW. If it is not checked, no CW output is used. Keying methods are:
- ttys - uses the control pins of a serial port. Pinout for D-SUB9:
- 4 DTR - CW
- 5 GND - ground
- 7 RTS - PTT
- ttys single pin - same as ttys for PTT and CW on a single pin (FT8x7 via DATA connector).
- Davac4 - USB SSB/CW keyer Davac4 by OK1ZIA. No device is required, it uses the USB device A600:E110 (or E111, E112). It needs the library libftdi.
- Davac5 - USB SSB/CW keyer Davac5 by OK1ZIA. It needs the library hidapi. The button Davac5 options opens its settings.
- cwdaemon - controls cwdaemon by Joop PG4I. Obsolete, not fully working (CQ repeat). Please use direct access to the keying device. You can also use M5 ESP32 CW keyer over TCP/IP.
- winkey - uses Winkey by K1EL. The button Winkey options opens its settings, see Winkey options.
- winkey TCP - uses Winkey over TCP/IP. On the other side, you can use a TCP to serial converter f.e. GetBlue or socat:
socat /dev/ttyUSB0,raw,echo=0 TCP-LISTEN:6789
- TCI - sends CW through the TCI protocol to the SDR program. See TCI.
- Hamlib - sends CW to the radio using Hamlib (only in the builds with Hamlib). Only some newer radios have support, sometimes with limitation (limited size of message, speed has to be set on the radio). Tucnak does not know when the radio finishes the message, so the repeated CQ is blind: the Delay in CW CQ is counted from the beginning of the message.
The parallel port is not supported any more. If your old configuration uses it, Tucnak writes a message to the log and the CW interface is off.
Keying device f.e. /dev/ttyS0, /dev/ttyUSB0, COM1.
Hostname and UDP port are the address of the other side for winkey TCP (the port is a TCP port in this case) and for cwdaemon (the hostname must be an IP address).
Initial speed says the keying speed in WPM after the program start. You can change it using the PageUp or PageDown keys.
Weight (30-70, default 50) changes the ratio of mark and space in CW. Tucnak makes the timing itself for ttys, Davac4 and Davac5. The length of the dot, the dash and the space after every dot or dash is:
- tdot = 24 000 × w / v [µs]
- tdash = 3 × tdot
- tspace = 24 000 × (100 − w) / v [µs]
Here w is the weight and v is the speed in WPM. With the weight 50 the dot is 1 200 000 / v [µs], it is the standard timing. Winkey and cwdaemon get the weight and make the timing themselves.
WPM range describes the speed that can be set with the PageUp/PageDown keys. The minimal WPM is also used for Winkey - it can handle only 31 speed steps. Normally the minimal speed is set to 10 WPM which means the winkey range 10-41 WPM. If you need for example 50 WPM, set the minimal WPM to at least 19.
Use speaker (only on Unix) - beeps using the program soundwrapper. Soundwrapper must be setuid to root to access /dev/console.
PTT lead in [ms] - (experimental feature) Tucnak turns on PTT some time before CW to key on TRX and PA's to prevent "eating" of the begin of the code. It also allows the TX chain to stabilise before sending. Suggest 100 -> 250 ms.
PTT tail [ms] - Tucnak keeps PTT on for this time after the end of CW.
Run mode aut. give after [chars] (0-9) - in CW mode, when you type a callsign in the input line, Tucnak starts to send the typed characters in CW after you have typed this number of characters. The other station then hears the callsign which you are typing. 0 means off.
PTT mouse button (only in the graphical mode) - the mouse button which works as PTT: TX is on while you press it, RX when you release it. 0 = off, 2 = middle, 3 = right, 4 = X1, 5 = X2.