Rig options
Tucnak uses Hamlib for accessing the rig (transceiver) via the CAT interface. You can use probably any interface which is working with other programs. Or you can build one of my RIG interfaces.
The item Setup -> Rig/TCI options opens a menu with the list of your rigs. You can connect more rigs. Every rig has the line Rig n (or your description), the lines of the disabled rigs end with (disabled). Select a rig to open its dialog. The menu also has Add rig and Remove rig. The last item is TCI (ExpertSDR3), the settings of the connection to the SDR program ExpertSDR3, see TCI. In Tucnak built without Hamlib the menu contains only TCI.

- Enabled: Quick enable/disable the rig.
- Description: Your description, will be shown in the menu.
- Device: Device where the interface is connected. Typically /dev/ttyS0, /dev/ttyUSB0. Under Windows COMx.
Note: Under Linux the user must be member of the group dialout to access the device. Under OpenSuse also member of the lock group. Add it as root: adduser <user> <group> and relogin.
- Rig model: Model number of the rig defined by Hamlib. You can obtain it by running the command rigctl -l or you can use:
- Choose: Press the button to show a menu. In the first level you choose the manufacturer, in the second level the rig model. The model number is written to Rig model, the rig name is written to Description if it is empty.
- Config: Hamlib parameters for the radio. Read the Hamlib documentation for the exact syntax. Example: ptt_type=RTS
- Baudrate: Communication speed. Leave 0 to use the default Hamlib value.
- Force handshake NONE: For rigs which have the handshake set in Hamlib defaults but you do not want to use the handshake. For example TS-850S connected only using RX/TX pins.
- CIV address (hex): Address of the rig if you have more Icom radios connected via one interface. Enter 0 for the default address. The address is written in hexadecimal.
- Freq. shift SSB->CW: Some old radios (Icom, Kenwood) shift the frequency when changing the mode SSB <--> CW. If you call CQ on SSB and someone calls you in CW, you must switch to CW and tune for about 800 Hz up. Tucnak can compensate this shift when you use Alt+M to switch the mode. The value is from -2000 to +2000 Hz.
- Transverter's LO QRG [Hz]: is the frequency which Tucnak adds to the frequency read from the CAT of the transceiver and the result is shown on the screen:
- fdisplay = fCAT + fLO (all in Hz)
Note: some radios support the transceiver mode, for example the radio is tuned to 14 MHz, CAT reports also 14 MHz but the display of the transceiver shows 144 MHz.
The LO frequency must be computed by the operator, you can use Fix QRG in the Edit menu. This is the LO of the rig. If the band has its own LO in Band defaults and it is not 0, Tucnak uses the LO of the band instead. So with more transverters on one rig set the LO for each band in Band defaults.
- Rig poll interval [ms]: How often Tucnak asks the radio. Set a higher value if the communication with the radio produces system load or the radio gets frozen (old TS-850S). The value is from 30 to 9999 ms, the default for a new rig is 300 ms.
- Set band from radio: The band in the log is switched automatically when the radio is tuned to another band.
- Change band on radio: The band of the radio is changed when the operator switches the band in the log.
- Change mode on radio: The mode of the radio is changed when the operator changes the mode.
- Set PTT on radio: How Tucnak keys PTT using Hamlib. The button offers Unused, PTT, PTT MIC and PTT DATA.
- Clear RIT on RUN's QSO save: in the Run mode Tucnak clears RIT after the QSO is stored. Depends on the radio and Hamlib.
- Debug rig: Extra debugging information is written to the Log window.
Problems
Bus error on ICOM
If you use an ICOM TRX, Tucnak can report Error on bus or Bus Collision. It is caused by the CI-V TRN option turned on. In this case the TRX is broadcasting the current frequency over the CI-V interface which collides with the communication of Tucnak. Read the manual how to turn it off.
- IC-706: Press LOCK and power the rig on. Press MENU and search for the menu item CI-V TRN (item 36 or 37). Rotate the main dial to set it to OFF. Then turn the rig off.
- IC-7400: In the menu set CI-V Transceive to OFF
- TS-590SG: The radio requires hardware handshake when you use the USB port. The Force handshake NONE must be turned off.
I/O error on new ICOMs
New ICOMs with a USB connector (IC-7610) can output I/O error. To fix it, open the menu and set CI-V USB Echo Back to ON. TNX to OK1FIK.
FT-991
The Yaesu USB driver creates two serial ports, enhanced and standard. The first one can be used as CAT, the second as CW keying. In Rig options set:
- Rig model: choose the FT-991 (Yaesu) with the button Choose
- Baudrate to 4800
- PTT on radio set to PTT MIC
Radio setup:
- 031 CAT RATE 4800
- 032 CAT TOT 100 msec
- 033 CAT RTS Enable
- 056 CW BK-IN TYPE SEMI
- 060 PC KEYING DTR
- 071 DATA PTT SELECT RTS
- 072 DATA PORT SELECT USB
- 106 SSB MIC SELECT MIC
- 108 SSB PTT SELECT DAKY
- 109 SSB PORT SELECT USB
Thanks to OK2WO and DL5ZA
IC-705
- Rig model: choose the IC-705 (Icom) with the button Choose
- Baudrate to: 115200
- CI-V Address: 94h
Radio setup:
- CI-V Address 94h
- CI-V Transceive ON
- CI-V USB Echo Back ON
Thanks to OK1UGE
Linux Can't open rig /dev/ttyUSB0 ... I/O error
Check if the current user has access to /dev/ttyUSB0. The simplest access is based on a group:
contest ~$ ls -l /dev/ttyUSB* crw-rw---- 1 root dialout 188, 0 Jan 12 11:40 /dev/ttyUSB0
You have to be a member of dialout
contest ~$ id uid=1000(ok1zia) gid=1000(ok1zia) groups=1000(ok1zia),8(mail),24(cdrom),25(floppy),29(audio)
Dialout is missing, use adduser:
contest ~$ sudo adduser ok1zia dialout Adding user `ok1zia` to group `dialout' ... Adding user ok1zia to group dialout Done. contest ~$ id uid=1000(ok1zia) gid=1000(ok1zia) groups=1000(ok1zia),8(mail),20(dialout),24(cdrom),25(floppy),29(audio)
No SSB modulation on Yaesu (FT-8x7)
Try to turn off the speech processor.